锻造模具用材，如螺丝螺帽模具、汽车行业和机械制造行业模具等
| 外径 mm | 公差 | 高度mm | 公差 | 内孔mm | 公差 | 大小头mm | 同心度⊙mm |
| 10 | 5.0-50.0 | 0.8-2.0 | |||||
| 12 | 5.0-50.0 | 0.8-2.0 | |||||
| 14 | 5.0-50.0 | 0.8-3.0 | |||||
| 15 | 5.0-60.0 | 0.8-3.0 | |||||
| 18 | 5.0-60.0 | 0.8-3.0 | |||||
| 20 | 5.0-80.0 | 0.8-3.0 | |||||
| 22 | 5.0-80.0 | 0.8-5.0 | |||||
| 25 | 5.0-80.0 | 0.8-10.0 | |||||
| 30 | 5.0-80.0 | 0.8-15.0 | |||||
| 35 | 5.0-100.0 | 0.8-15.0 | |||||
| 40 | 5.0-100.0 | 0.8-15.0 | |||||
| 45 | 5.0-100.0 | 0.8-15.0 | |||||
| 50 | 5.0-100.0 | 0.8-20.0 | |||||
| 55 | 5.0-150.0 | 0.8-25.0 | |||||
| 60 | 5.0-150.0 | 0.8-30.0 | |||||
| 65 | 5.0-150.0 | 0.8-30.0 | |||||
| 70 | 5.0-150.0 | 0.8-30.0 | |||||
| 80 | 5.0-150.0 | 0.8-35.0 | |||||
| 90 | 5.0-150.0 | 0.8-45.0 | |||||
| 100 | 5.0-150.0 | 0.8-50.0 |
| 材质表 | |||||
| 材种 | 材种名 | 比重(g/cm3) | 硬(HRA) | 抗折力(GPa) | K1C(m1/2) |
| AU | AU05 | 14.7 | 93.2 | 3.6 | 9.1 |
| AU10 | 14.5 | 92.7 | 3.8 | 9.5 | |
| AU25 | 14.2 | 92 | 3.9 | 10.2 | |
| AU35 | 14 | 91.5 | 3.9 | 10.6 | |
| AU50 | 13.7 | 90.7 | 3.9 | 11.3 | |
| AD | AD08 | 14.6 | 92 | 3.5 | 10 |
| AD10 | 14.5 | 91.5 | 3.6 | 10.4 | |
| AD20 | 14.2 | 90.7 | 3.7 | 11.1 | |
| AD30 | 14 | 90 | 3.8 | 11.9 | |
| AD50 | 13.7 | 89 | 3.8 | 12.7 | |
| AG | AG25 | 14.7 | 91 | 3.4 | 12.8 |
| AG35 | 14.5 | 90.2 | 3.5 | 14.1 | |
| AG50 | 14.3 | 89 | 3.6 | 15.3 | |
| AG60 | 14.1 | 88 | 3.7 | 16.5 | |
| AG70 | 13.9 | 87 | 3.6 | 17.6 | |
| AG80 | 13.6 | 86 | 3.4 | 18.7 | |
| AT | AT40 | 14.2 | 87 | 3.5 | 21 |
| AT55 | 13.9 | 86 | 3.4 | 22.1 | |
| AT70 | 13.6 | 85 | 3.2 | 23.2 | |
| AT80 | 13.4 | 84.5 | 2.9 | 24 | |
| AT90 | 13.2 | 83 | 2.6 | 24.7 | |
| AT95 | 13 | 82 | 2.1 | 25.5 | |
| AM | AM20 | 14.9 | 91 | 3.4 | 15 |
| AH | AH10 | 14.5 | 91.8 | 3.7 | 10.1 |
| AH12 | 14.3 | 92.2 | 3.9 | 12.2 | |
| 材质推荐表 | ||||
| 用途系列 | 材种名 | 相当材种 | 用途例 | 金相写真 |
| 超微细加工用（超微粒子） | AU05 | TSM20 | 超微细加工用,如半导体,IC封装,引线框模具 | |
| AU10 | H10F/TSM30/EF05 | |||
| AU25 | F10/TSM40/FB15/EF10 | |||
| AU35 | H15F/MG30 | |||
| AU50 | EF20/FB20 | |||
| 微细加工用（细粒） | AD08 | KD05 | 连接器、端子冲压,马达铁芯动压连续冲模,粉未冶金模具,拉拔模具 | |
| AD10 | NC6/CF/H25S/KD10 | |||
| AD20 | CF-H40S/KD20 | |||
| AD30 | CD650 | |||
| AD50 | KD40 | |||
| 韧性高的通用材质（中粒） | AG25 | H20S/KG2 | 马达铁芯冲压,粉未冶金模具,拉拔模具,锻造模具 | |
| AG35 | H30S/KG3 | |||
| AG50 | H40S/KG5 | |||
| AG60 | NC8/KG6 | |||
| AG70 | H50S | |||
| AG80 | ||||
| 锻造型等耐冲击性材质（粗粒） | AT50 | B40S | ||
| AT55 | NC12/ST6 | 白铁,不锈钢螺丝模 | ||
| AT70 | ST7/EA65/VA70 | M20以下螺丝模具/白铁,不锈钢螺丝模 | ||
| AT80 | NC14/VA80 | 20∮-50∮螺丝模六片模 | ||
| AT90 | NC16/VA90 | 螺帽模,M20以上螺丝模 | ||
| AT95 | EA90/VA95 | 高冲击性模具 | ||
| 特殊用途 | AM20 | MC20 | 纯铜、纯铁的冲压模具 | |
| 刀具用材质 | AH10 | H10F | 刀具 | |
| AH12 | TSF44,TF25 | 钛合金、镍合金刀具 |
| |
Copyright © 昆山西诺巴精密模具有限公司地址：昆山市长江北路928号10号厂房 备案号：苏ICP备14004261号-3
服务热线
